Font gost type a bold.

GOST 2.304-81

Group T52

INTERSTATE STANDARD

Unified system of design documentation

DRAWING FONTS

Unified system for design documentation. Letters for drawings

ISS 01.080.30

Introduction date 1982-01-01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the USSR State Committee for Standards

2. APPROVED AND INTRODUCED BY Decree of the State Committee of the USSR for Standards dated March 28, 1981 N 1562

Change No. 2 was adopted by the Interstate Council for Standardization, Metrology and Certification by correspondence (Minutes No. 23 dated February 28, 2006)

The national standardization bodies of the following states voted for the adoption of the change: AZ, AM, BY, KZ, KG, MD, RU, TJ, TM, UZ, UA [alpha-2 codes according to MK (ISO 3166) 004]

3. (Deleted, Rev. N 2).

4. REPLACE GOST 2.304-68

5. EDITION (August 2007) with Amendment No. 1, approved in March 1989, June 2006 (IUS 7-89, 9-2006)

This standard establishes drawing fonts applied to drawings and other technical documents of all industries and construction.

1. TERMS AND DEFINITIONS

1.1. Font size- the value determined by the height of capital letters in millimeters.

1.2. The height of capital letters is measured perpendicular to the base of the line.

The height of lowercase letters is determined from the ratio of their height (without processes) to the font size, for example, = 7/10 (Fig. 1 and 2).

1.3. Letter width- the maximum width of the letter, measured in accordance with drawings 1 and 2, is determined in relation to the font size, for example, 6/10, or in relation to the thickness of the font line, for example, 6

1.4. Font Line Thickness- thickness, determined depending on the type and height of the font.

1.5. Auxiliary grid- a grid formed by auxiliary lines into which letters fit. The pitch of the auxiliary grid lines is determined depending on the thickness of the font lines (Fig. 3).

Heck. 3

2. TYPES AND SIZES OF FONT

2.1. The following font types are installed:

type A without slope (=1/14) with the parameters given in Table 1;

type A with an inclination of about 75° (=1/14) with the parameters given in Table 1;

type B without slope (=1/10) with the parameters given in Table 2;

type B with an inclination of about 75° (=1/10) with the parameters given in Table 2.

Table 1

Type A font (=)


Font options	Denomination- meaning	Relative size	Dimensions, mm
Font size:
capital letter height
lower case height
Letter spacing


Font Line Thickness

table 2

Type B font (=)


Font options	Designation	Relative size	Dimensions, mm
Font size:
capital letter height
lower case height
Letter spacing
Minimum row spacing (auxiliary grid height)
Minimum spacing between words
Font Line Thickness

Notes:

1. The distance between letters whose adjacent lines are not parallel to each other (for example, GA, AT) can be halved, i.e. on the line thickness of the font.

2. The minimum distance between words separated by a punctuation mark is the distance between the punctuation mark and the word following it.

When executing documents in an automated way, it is allowed to use fonts used by computer technology. In this case, their storage and transfer to users of documents should be ensured.

(Changed edition, Rev. N 2).

2.2. The following font sizes are set: (1.8); 2.5; 3.5; 5; 7; ten; fourteen; 20; 28; 40.

Note. The use of font size 1.8 is not recommended and is only allowed for type B.

2.3. The construction of the font in the auxiliary grid is shown in Figure 4.

2.4. Limit deviations of the sizes of letters and numbers ±0.5 mm.

3. RUSSIAN ALPHABET (CYRILLIC)

3.1. Font type A with a slope is shown in Figure 5.

3.2. Font type A without tilt is shown in Figure 6.

3.3. Font type B with a slope is shown in Figure 7.

3.4. Font type B without tilt is shown in Figure 8.

4. LATIN ALPHABET

4.1. Font type A with a slope is shown in Figure 9.

4.2. Font type A without tilt is shown in Figure 10.

Damn.10

4.3. Font type B with a slope is shown in Figure 11.

Damn 11

4.4. Font type B without tilt is shown in Figure 12.

Devil 12

4.5. The types, shape and arrangement of diacritical marks for fonts of types A and B without italics are given in the reference appendix.

Diacritics for italic fonts should follow the same rules.

5. GREEK ALPHABET

5.1. Font type A with a slope is shown in Figure 13.

Damn.13

5.2. Font type A without tilt is shown in Figure 14.

Devil 14

5.3. Font type B with a slope is shown in Figure 15.

Damn.15

5.4. Font type B without tilt is shown in Fig.16.

Devil 16

5.5. The names of the letters of the Greek alphabet, shown in Fig. 13-16:
















		omicron

6. ARABIC AND ROMAN NUMBERS

6.1. Font type A is shown in Figure 17.

Damn.17

6.2. Font type B is shown in Fig.18.

Damn.18

Notes:

1. Roman numerals L, C, D, M should be performed according to the rules of the Latin alphabet.

2. Roman numerals may be limited to horizontal lines.

7. SIGNS

7.1. Font type A with a slope is shown in Figure 19.

Damn.19

7.2. Font type A without tilt is shown in Figure 20.

Damn.20

7.3. Font type B with a slope is shown in Fig.21.

Damn.21

7.4. Font type B without tilt is shown in Figure 22.

Damn.22

7.5. The names of the signs are given in Table 3.

Table 3


Numbers of characters in the drawings	Name of signs

	Colon

	Semicolon
	Exclamation point
	Question mark


	Paragraph
	Equality
	Value after rounding
	Corresponds
	Asymptotically equal to
	Approximately equal to


	Less or equal
	More or equal

	Minus, dash
	plus or minus
	Multiplication





	Parallel
	Perpendicular


	Taper




	Integral
	Infinity
	Square brackets
	Round brackets
	Fraction dash


	Similarity sign
	Star

8. RULES FOR WRITING FRACTIONS, INDICATORS, INDICES AND MAXIMUM DEVIATIONS

8.1. Fractions, indicators, indices and limit deviations are performed in accordance with Table 4, font size:

one step smaller than the font size of the main value to which they are assigned;

the same size as the font size of the main size.

Table 4


Implementation options	Fonts		Execution examples
	basic- nye ranks	fractions, bye- zatels, etc.
The font size is one step smaller than the base size


The font size is the same as the size of the main value

APPENDIX (reference). DIACCRITICS

APPENDIX
Reference

Hungarian

German

Polish language

Romanian language

Czech and Slovak

Electronic text of the document
prepared by Kodeks JSC and verified against:
official publication
Unified system of design documentation:
Sat. GOSTs. - M.: Standartinform, 2007

Introduction date 01.01.82

This standard establishes drawing fonts applied to drawings and other technical documents of all industries and construction.

1. TERMS AND DEFINITIONS

1.1. Font size h - value determined by the height of capital letters in millimeters.1.2. The height of uppercase letters h is measured perpendicular to the base of the line. The height of lowercase letters c is determined from the ratio of their height (without processes k) to the font size h, for example, c = 7/10 h (Fig. 1 and 2).

1.3. The width of the letter g is the largest width of the letter, measured in accordance with the drawing. 1 and 2 is determined in relation to the font size h, for example, g = 6/10 h, or in relation to the thickness of the font line d, for example, g = 6 d.1.4. The thickness of the font line d is the thickness determined depending on the type and height of the font.1.5. Auxiliary grid - a grid formed by auxiliary lines into which letters fit. The step of the auxiliary grid lines is determined depending on the thickness of the font lines d (Fig. 3).

2. TYPES AND SIZES OF FONT

2.1. The following types of font are installed: type A without inclination (d = 1/14 h) with the parameters given in Table. 1; type A with an inclination of about 75° (d = 1/14 h) with the parameters given in Table. 1; type B without slope (d = 1/10 h) with the parameters given in Table. 2; type B with an inclination of about 75° (d = 1/10 h) with the parameters given in Table. 2.

Table 1

Font type A (d = h/14)

Font options	Designation	Relative size	Dimensions, mm
Font size -
capital letter height
lower case height
Letter spacing


Font Line Thickness

table 2

Type B font (d = h/10)

Font options	Designation	Relative size	Dimensions, mm
Font size -
capital letter height
lower case height
Letter spacing
Minimum row spacing (auxiliary grid height)
Minimum spacing between words
Font Line Thickness

Notes: 1. The distance a between letters whose adjacent lines are not parallel to each other (for example, GA, AT) can be reduced by half, i.e. by the thickness d of the font line. 2. The minimum distance between words e separated by a punctuation mark is the distance between the punctuation mark and the word following it. When executing documents in an automated way, it is allowed to use fonts used by computer technology. In this case, their storage and transfer to users of documents should be ensured. (Changed edition, Rev. No. 2) 2.2. The following font sizes are set: (1.8); 2.5; 3.5; 5; 7; ten; fourteen; 20; 28; 40. Note. The use of font size 1.8 is not recommended and is allowed only for type B.2.3. The construction of the font in the auxiliary grid is shown in Fig. 4.

2.4. Limit deviations of the sizes of letters and numbers ± 0.5 mm.

3. RUSSIAN ALPHABET (CYRILLIC)

3.1. Font type A with a slope is shown in Fig. 5

3.2. Font type A without tilt is shown in Fig. 6.

3.3. Font type B with a slope is shown in Fig. 7.

3.4. Font type B without tilt is shown in Fig. eight.

4. LATIN ALPHABET

4.1. Font type A with a slope is shown in Fig. nine.

4.2. Font type A without tilt is shown in Fig. ten.

4.3. Font type B with a slope is shown in Fig. eleven.

4.4. Font type B without tilt is shown in Fig. 12.

4.5. Types, shape and arrangement of diacritical marks for fonts of types A and B without italics are given in the reference appendix. Diacritical marks for fonts with italics should follow the same rules.

5. GREEK ALPHABET

5.1. Font type A with a slope is shown in Fig. thirteen.

5.2. Font type A without tilt is shown in Fig. fourteen.

5.3. Font type B with a slope is shown in Fig. fifteen.

5.4. Font type B without tilt is shown in Fig. sixteen.

5.5. The name of the letters of the Greek alphabet shown in Fig. 13 - 16:

6. ARABIC AND ROMAN NUMBERS

6.1. Font type A is shown in Fig. 17.

6.2. Font type B is shown in Fig. eighteen.

Notes: 1. Roman numerals L, C, D, M should be performed according to the rules of the Latin alphabet. 2. Roman numerals may be limited to horizontal lines.

7. SIGNS

7.1. Font type A with a slope is shown in Fig. nineteen.

7.2. Font type A without tilt is shown in Fig. 20.

7.3. Font type B with a slope is shown in Fig. 21.

7.4. Font type B without tilt is shown in Fig. 22.

7.5. The names of the signs are given in Table. 3.

Table 3

Numbers of characters in the drawings	Name of signs	Numbers of characters in the drawings	Name of signs
1	Dot	25	Percent
2	Colon	26	Degree
3	Comma	27	Minute
4	Semicolon	28	Second
5	Exclamation point	29	Parallel
6	Question mark	30	Perpendicular
7	Quotes	31	Injection
8	And	32	slope
9	Paragraph	33	Taper
10	Equality	34	Square
11	Value after rounding	35	Arc
12	Corresponds	36	Diameter
13	Asymptotically equal to	37	Radical
14	Approximately equal to	38	Integral
15	Smaller	39	Infinity
16	More	40	Square brackets
17 and 17a	Less or equal	41	Round brackets
18 and 18a	More or equal	42	Fraction dash
19	Plus	43	Number
20	Minus, dash	44	From to
21	plus or minus	45	Similarity sign
22,23	Multiplication	46	Star
24	Division

8. RULES FOR WRITING FRACTIONS, INDICATORS, INDICES AND MAXIMUM DEVIATIONS

8.1. Fractions, indicators, indices and limit deviations are performed in accordance with Table. 4 font size: one step smaller than the font size of the main size to which they are assigned; the same size as the font size of the main size.

Table 4

Implementation options			Execution examples
	basic quantities	fractions, indicators, etc.
The font size is one step smaller than the base size


The font size is the same as the size of the main value

APPENDIX

Reference

DIACCRITICS

Hungarian

German

Polish language

Romanian language

Czech and Slovak

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the USSR State Committee for Standards2. APPROVED AND INTRODUCED BY Decree of the USSR State Committee for Standards No. 15623 dated March 28, 1981. (Excluded, Amendment No. 2)4. INSTEAD OF GOST 2.304-685. Edition (July 2001) with Amendment No. 1 approved in March 1989 (IUS 7-89)

Welcome to site site! Friends, on our site you can find a lot of interesting and useful things for yourself, your loved ones and children. We offer a huge range brushes , framework , styles , figures , icons and many other additions to your photo.

Photoshop frames

Particularly popular are frames for photoshop, with which you can decorate your photo without any effort. You just need to find a suitable frame, insert your photo, which will serve as a creative decoration for your workplace or family album. Also, you can create a fun room for your baby. A large selection will help you with this. children's frames. Even novice users can master these types of frames.
We draw your attention to wedding photo frames , for family photo , vignettes , for lovers , "for you" , congratulations , calendars , Great Easter February 23 , Happy New Year , For birthday , for valentine's day. All these frames can be downloaded from this link

Download templates for photoshop

It's time to talk about the main section of our site - "Photo Templates". First of all, it is popular among girls of different age categories. After all, a girl always strives for charm and beauty. It is in this section, dear girls, that you can be in the image: a stranger in the moonlight or vice versa, a good fairy. You just need to go to this link. Let's not forget about our dear men, because our site has also prepared many interesting templates for them, in the image of which a man will feel himself: a hardworking gardener, a musketeer, a knight, a pilot, a biker, a cowboy, a king, an iron man, a German officer, a race car driver, etc. .p. And all this absolutely free, just click on the mouse button and .

Dear users, the administration of our site has prepared a surprise for your children: section "Templates for children". Your child will feel like: a sweet bunny, a little one, a pirate, a duckling, a spider, a king, an elf, etc. Click the mouse faster and follow the link and get a lot of fun.
We recommend that you pay attention to the section "Icons". We offer a large selection of not only "frames", but also "icons". You can use this section for different purposes - from ordinary amateur photography to a large-scale design project. Here you can find a lot of exciting things!

Our site does not stand still, we are constantly developing, filling the site with useful information and, of course, listening to the opinions of users. You can leave all your comments and suggestions in the "Feedback" section. Site administration!